Product ManualDB35 SeriesTM100347671Rev. DAugust 2007ST3400832ACEST3300831ACEST3250823ACEST3200826ACE
4DB35 Series Product Manual, Rev. D*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending o
DB35 Series Product Manual, Rev. D52.2 Formatted capacity*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacit
6DB35 Series Product Manual, Rev. D2.4 Physical characteristics2.5 Seek timeSeek measurements are taken with nominal power at 25°C ambient temperature
DB35 Series Product Manual, Rev. D72.7 Power specificationsThe drive receives DC power (+5V and +12V) through a four-pin standard drive power connecto
8DB35 Series Product Manual, Rev. D2.7.1.1 Typical current profileFigure 1 Typical 5V startup and operation current profileFigure 2 Typical 12V star
DB35 Series Product Manual, Rev. D92.7.4 Power-management modesThe drive provides programmable power management to provide greater energy efficiency.
10DB35 Series Product Manual, Rev. D2.8.2 Temperature gradient2.8.3 Humidity2.8.3.1 Relative humidity2.8.3.2 Wet bulb temperature2.8.4 Altitude2.8.5 S
DB35 Series Product Manual, Rev. D112.8.6.2 Nonoperating vibrationThe following table lists the maximum nonoperating vibration that the drive may expe
12DB35 Series Product Manual, Rev. D2.11 Reliability2.12 Agency certification2.12.1 Safety certificationThe drives are recognized in accordance with U
DB35 Series Product Manual, Rev. D13Australian C-Tick (N176)If these models have the C-Tick marking, they comply with the Australia/New Zealand Standa
Copyright © 2005-2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A.Publication number: 100347671, Rev. D August 2007Seagate, Seagate
14DB35 Series Product Manual, Rev. D2.13 Environmental protectionSeagate designs its products to meet environmental protection requirements worldwide,
DB35 Series Product Manual, Rev. D153.0 Configuring and mounting the driveThis section contains the specifications and instructions for configuring an
16DB35 Series Product Manual, Rev. D3.2 Breather filter hole precautionsThis section contains information regarding the precautions which should be ta
DB35 Series Product Manual, Rev. D173.3 Jumper settings3.3.1 Master/slave configurationThe options jumper block shown in Figure 4 is used to configure
18DB35 Series Product Manual, Rev. DWindows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacitiesgreater than 32 G
DB35 Series Product Manual, Rev. D19Figure 6 Mounting dimensions—top, side and end viewNotes:1. Dimensions are shown in inches (mm).2 Dimensions per
20DB35 Series Product Manual, Rev. D
DB35 Series Product Manual, Rev. D214.0 ATA interfaceThese drives use the industry-standard ATA task file interface that supports 16-bit data transfer
22DB35 Series Product Manual, Rev. D4.1.1 Supported ATA commandsThe following table lists ATA-standard commands that the drive supports. For a detaile
DB35 Series Product Manual, Rev. D23Security Disable Password F6HSecurity Erase Prepare F3HSecurity Erase Unit F4HSecurity Freeze F5HSecurity Set Pass
DB35 Series Product Manual, Rev. DiContents1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24DB35 Series Product Manual, Rev. D4.1.2 Identify Device commandThe Identify Device command (command code ECH) transfers information about the drive
DB35 Series Product Manual, Rev. D2554 Number of current logical cylinders xxxxH55 Number of current logical heads xxxxH56 Number of current logical
26DB35 Series Product Manual, Rev. DNote. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supportedNote. See
DB35 Series Product Manual, Rev. D274.1.3 Set Features commandThis command controls the implementation of various features that the drive supports. Wh
28DB35 Series Product Manual, Rev. DSeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that elimi-nate
DB35 Series Product Manual, Rev. D295.0 Seagate Technology support servicesInternetFor information regarding Seagate products and services, visit www.
30DB35 Series Product Manual, Rev. DCustomer Service OperationsWarranty ServiceSeagate offers worldwide customer support for Seagate products. Seagate
DB35 Series Product Manual, Rev. D31IndexNumerics3D Defense System 1Aacoustics 11Active mode 9agency certification (regulatory) 12alternate ca
32DB35 Series Product Manual, Rev. DHhandling 15heads 1height 6humidity 10II/O data-transfer rate 5Identify Device 22Identify Device comma
DB35 Series Product Manual, Rev. D33SS.M.A.R.T. commands 27S.M.A.R.T. Disable Operations 23S.M.A.R.T. drive monitoring 1S.M.A.R.T. Enable/Disabl
iiDB35 Series Product Manual, Rev. D
34DB35 Series Product Manual, Rev. D
Seagate Technology LLC920 Disc Drive, Scotts Valley, California 95066-4544, USAPublication Number: 100347671, Rev. D, Printed in U.S.A.
DB35 Series Product Manual, Rev. DiiiList of FiguresFigure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . .
ivDB35 Series Product Manual, Rev. D
DB35 Series Product Manual, Rev. D11.0 IntroductionThis manual describes the functional, mechanical and interface specifications for the following Sea
2DB35 Series Product Manual, Rev. D
DB35 Series Product Manual, Rev. D32.0 Drive specificationsUnless otherwise noted, all specifications are measured under ambient conditions, at 25°C,
Comments to this Manuals