Seagate STT8000A Manual Page 26
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Installation
Page 18 STT8000A Product Manual
6. Secure the drive using the mounting screws. The threaded mounting brackets
are designed for M3.0 metric screws. If you are mounting the drive in a 3.5-inch
bay, use the screw supplied with the drive. Do not substitute other screws.
Using longer screws may damage the drive. If slide rails are needed, use the
plastic slide rails (supplied with the drive in some configurations).
7. Connect an available power cable to the power connector on the drive. Figure
3-1 shows the location of the power connector. The recommended power
mating connector requires an AMP 1-48024-0 housing with AMP 60617-1 pins
or equivalent.
Note:
Turn off all power before inserting connectors.
8. Connect the interface cable with the connector on the rear of the unit. When
you make the connection, be sure pin 1 of the connector aligns with pin 1 on
the cable connector. See Figure 3-1 for the location of the connector and the
Pin 1 location.
Note:
Pin 1 on the connector on the rear of the drive is to your right as you look at
the back of the drive (right side up). (See Figure 3-1.) Your cable should
have Pin 1 highlighted by a color or dark strip. Be sure to mate Pin 1 on the
cable to Pin 1 on the drive. Failure to do so could make the drive
inoperative. Also, the cable is keyed to prevent incorrect installation. Make
sure that the blocked pin in the cable connector coincides with the missing
pin on the connector on the rear of the drive. (See Figure 3-1.)
9. Replace the computer cover. Be sure to reconnect any peripherals that you
disconnected during the installation.
10. Plug the computer and any peripherals into an AC power outlet.
11. Start the computer and install your tape backup software.
Mounting dimensions
Figures 3-4 and 3-5, respectively, show the location of the mounting holes for the
internal drive without and with mounting brackets.
- STT8000A 1
- ATAPI Minicartridge Drive 1
- Product Manual 1
- Technology, Inc 2
- FCC Notice 3
- Table of Contents 5
- ATAPI interface 31 6
- Tape format 63 7
- Theory of operations 69 7
- Glossary 73 8
- Acronyms and measurements 77 8
- Introduction 9
- Figure 1-1 10
- Features 11
- Typical system configurations 12
- Flash EEPROM 13
- Software 13
- References 13
- About this manual 14
- Specifications 15
- Figure 2-1 16
- Figure 2-2 16
- Power specifications 17
- Performance specifications 18
- Environmental requirements 19
- Mean-Time-Between Failures 20
- Mean-Time-To-Repair 20
- Recommended tapes 21
- Tape capacities and formats 21
- Regulatory compliance 22
- Installation 23
- Handling guidelines 23
- Setting jumpers 24
- Installing the drive 25
- Mounting dimensions 26
- Figure 3-4 27
- Figure 3-5 27
- Chapter 3 Installation 28
- Installation Chapter 3 29
- DRIVE ACTIVE 31
- Using Travan cartridges 32
- Figure 4-4 33
- Figure 4-5 33
- Caring for tape cartridges 35
- Caring for the drive 35
- Capstan Tape Head 36
- Troubleshooting 37
- ATAPI interface 39
- ATA-2 Signals 39
- ATA registers 40
- ATAPI Interface Chapter 5 41
- Supported ATA Commands 42
- Chapter 5 ATAPI Interface 44
- Erase command 47
- Inquiry command 48
- Load/Unload command 49
- Locate command 50
- Log Select command 51
- Log Sense command 52
- Error Counter Page (Read) 53
- Tape Capacity Page Code 54
- Mode Select command 55
- Mode Sense command 56
- Mode Parameter Header 57
- Mode Block Descriptor 57
- Mode Medium Partition Page 58
- Mode Tape Parameters Page 59
- Read command 60
- Read Position command 61
- Request Sense command 63
- Rewind command 65
- Space command 66
- Test Unit Ready command 67
- Write command 68
- Write Filemark command 69
- Tape format 71
- Track numbering 72
- Track format 72
- Figure 6-1 73
- General track layout 73
- Figure 6-2 73
- General frame layout 73
- Tape reference servo pattern 74
- Write equalization 75
- Randomization 75
- Chapter 6 Tape format 76
- Overview 77
- Block diagram 77
- Cartridge load mechanism 78
- Capstan drive motor assembly 78
- Control circuits 79
- Head design 79
- Sensors and switches 79
- Media—Travan minicartridges 80
- Glossary 81
- Appendix A Glossary 82
- Glossary Appendix A 83
- Acronyms and measurements 85
- Units of measurement 87
Related products and manuals for Tape drives Seagate STT8000A
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.248 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals