Seagate ST373454 Manual download pdf (Page 20)

10 Cheetah 15K.3 SCSI Product Manual, Rev. G

requested by the host with a Read command is retrieved from the buffer (if it is there), before any disc access

is initiated. If cache operation is not enabled, the buffer (still segmented with required number of segments) is

still used, but only as circular buffer segments during disc medium read operations (disregarding Prefetch

operation for the moment). That is, the drive does not check in the buffer segments for the requested read

data, but goes directly to the medium to retrieve it. The retrieved data merely passes through some buffer seg-

ment on the way to the host. On a cache miss, all data transfers to the host are in accordance with buffer-full

ratio rules. On a cache hit the drive ignores the buffer-full ratio rules. See explanations associated with Mode

page 02h (disconnect/reconnect control) in the

SCSI Interface Product Manual

The following is a simplified description of a read operation with cache operation enabled:

Case A - A Read command is received and the first logical block (LB) is already in cache:

1. Drive transfers to the initiator the first LB requested plus all subsequent contiguous LBs that are already in

the cache. This data may be in multiple segments.

2. When the requested LB is reached that is not in any cache segment, the drive fetches it and any remaining

requested LBs from the disc and puts them in a segment of the cache. The drive transfers the remaining

requested LBs from the cache to the host in accordance with the disconnect/reconnect specification men-

tioned above.

3. If the prefetch feature is enabled, refer to Section 4.5.2 for operation from this point.

Case B - A Read command requests data, the first LB of which is not in any segment of the cache:

1. The drive fetches the requested LBs from the disc and transfers them into a segment, and from there to

the host in accordance with the disconnect/reconnect specification referred to in case A.

2. If the prefetch feature is enabled, refer to Section 4.5.2 for operation from this point.

Each buffer segment is actually a self-contained circular storage (wrap-around occurs), the length of which is

an integer number of disc medium sectors. The wrap-around capability of the individual segments greatly

enhances the buffer’s overall performance as a cache storage, allowing a wide range of user selectable config-

urations, which includes their use in the prefetch operation (if enabled), even when cache operation is disabled

(see Section 4.5.2). The number of segments is set dynamically by the drive and cannot be set by the host.

The size in Kbytes of each segment is not reported by the Mode Sense command page 08h, bytes 14 and 15.

The value 0XFFFF is always reported. If a size specification is sent by the host in a Mode Select command

(bytes 14 and 15) no new segment size is set up by the drive, and if the STRICT bit in Mode page 00h (byte 2,

bit 1) is set to one, the drive responds as it does for any attempt to change unchangeable parameters (see

SCSI Interface Product Manual

4.5.1 Caching write data

Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to

be written to the medium is stored in one or more segments while the drive performs the write command.

If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made avail-

able for future read cache hits. The same buffer space and segmentation is used as set up for read functions.

The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of

RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that

are to be written are already stored in the cache from a previous read or write command. If there are, the

respective cache segments are cleared. The new data is cached for subsequent Read commands.

If the number of write data logical blocks exceeds the size of the segment being written into, when the end of

the segment is reached, the data is written into the beginning of the same cache segment, overwriting the data

that was written there at the beginning of the operation. However, the drive does not overwrite data that has not

yet been written to the medium.

If write caching is enabled (WCE=1), then the drive may return GOOD status on a write command after the

data has been transferred into the cache, but before the data has been written to the medium. If an error

occurs while writing the data to the medium, and GOOD status has already been returned, a deferred error will

be generated.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 93 94

Comments to this Manuals

No comments

Seagate ST373454 Manual Page 20

Comments to this Manuals

Related products and manuals for Internal hard drives Seagate ST373454